ITC, is a leading manufacturers of electric and hydraulic metering pumps for the injection of chemicals and additives into a fluid network. Quality of our products is guaranteed and backed up by 15 years experience and an exhaustive control. They are self contained and highly resistant to chemical products.
Our range of products includes:
- Electric Modular Dosing Pump
- Electric Dosing Pump High Flow and Pressure
- Electromagnetic Dosing Pump
- Proportional Dosing Pump
- Hydraulic Injector Pump
- Controllers and Mixers
DOSING PUMPS & INJECTOR PUMPS
Electric Modular Dosing Pump
MultiFertic® - Piston and Diaphragm Metering Pumps
The MultiFertic® injection pump are heavy duty, high precision pumps for chemicals products and additives, made up of one driving module and 1 to 4 injection modules for 25 to 500 l/h. - 7.5 to 150 GPH
In the same injector can be connected several injection modules to apportion different products (INDEPENDENT INJECTION) or to increase the injection flow. By increasing the number of modules in the same injector, higher flow regularity is obtained, whereby in the 4 modules model an actually continuous flow is obtained.
Up to four different modules can be added at the same motor, piston or diaphragm made in:
- Piston: Polyethylene or Ceramic
- Diaphragm: Teflon
- Cylinder: Polyethylene, Stainless steel or PVDF
Electric Dosing Pump High Flow and Pressure
ElectroFertic®2000
The ElectroFertic®2000 metering pump is an electric piston dosing pump made up of a driving module and one or two injection modules of 500, 750, 1000 l/h (132, 198,234 GPH) with electronic regulation by means of an inverter
Electromagnetic Dosing Pump
Dositec®
The dosing pumps Dositec® are heavy duty, high precision, electric diaphragm pumps for dosing liquid products.
Features:
- Flow: 0 to 0.53 GPH/0 to 2.64 GPH
- Pressure: 145 PSI
- Power supply 230V 50/60Hz IP66
Dositec® -M
Features:
- Manual regulation by means of a potentiometer
- Adjustable pulses from 0 to 100% or from 0 to 20%
- Input for a level switch to stop the pump
Dositec® P
Features:
- Proportional Regulation by means of a digital signal
- Operating modes
- Proportional to an external pulse (Multipliers or Divider)
Dositec® -A
Analogical regulation by means of a 4/20mA signal
Dositec® pH
Features:
- pH Regulation by means of a on/off relay
- Measuring range 0-14, 4/20mA output
Dositec® -RX
Features:
- Redox regulation by means of a on/off relay
- Measuring range -1400mV + 1400mV, 4/20mA output
Proportional Dosing Pump
FP10®
The FP10® is a proportional volumetric dosing injector pump for the introduction and mixing of one or two chemicals products or additives into a fluid network. Hydraulic running with very low pressure loss
Features:
- Suggested working range: 1 - 10 m³/h (265-2650 GPH)
- Maximum working pressure: 10 BAR (145 PSI)
- Pressure loss of 10 m³/h at 4 BAR: 0.6 BAR (8.7 PSI)
- Working mechanism: Magnetic without maintenance
- Stop system: manual or hydraulic with low pressure loss
- Injection flow : 0 - 240 l/h (0 - 58 GPH)
- Regulation range: 0% - 2.4%
- Maximum suction height: 5m
- Made in PP, NBR, Inox,
- Seals made of Viton® fluoroelestomers.
- Proportional injection to the incoming main flow being independent of the working pressure
- A built-in anti-siphon valve
Hydraulic Injection Pump
Fertic®
Hydraulic injector pumps for the injection of liquid or soluble fertilizer into irrigation network. It is self contained, with no externals parts other than the connection hoses and with no water pressure lost in the irrigation pipes. A controller ca be connected that acts upon an electrical valve to start and stop the pump in the desired moment.
EcoFertic®
Small hydraulic injector pump for the injection of liquid or soluble fertilizer into irrigation network
